Corsair iCUE 5000X RGB SIGNATURE SERIES vs Thermaltake The Tower 600computed

Datasheet figures next to each other, and the airflow balance, pressure verdict and case air heating that the fans in each box compute to behind that case's own front. Calculated with the CaseFlow model, not measured.

Side by side

Corsair iCUE 5000X RGB SIGNATURE SERIESThermaltake The Tower 600
FormATX mid towerATX mid tower
Volume66.2 L66.1 L
Dimensions520 × 245 × 520 mm286 × 420 × 550 mm
Frontglass solid or glass frontglass solid or glass front
Fan mountsfront 3 × 120/140, top 3 × 120/140, rear 1 × 120/140, bottom 3 × 120/140front 3 × 120, top 3 × 120/140, rear 2 × 120/140, bottom 1 × 120/140, side 3 × 120/140
Radiator supportfront 360 mm, top 360 mm, bottom 360 mmside 420 mm
Dust filtersfront, top, bottomtop, bottom, side
GPU length400 mm400 mm
Cooler height170 mm210 mm
Stock fans3 × CORSAIR SP RGB ELITE (front)2 × CT140 (top)
Stock airflow, max rpm–0 in / 136 out CFM
Stock pressure verdictstock fans named but no datasheet - nothing computednegative: mid -136.2 CFM
Case air at 290 W–+3.9 K
Stock fan noise–33.5 dB(A)
All mounts, reference fans292 in / 264 out CFM 6 / 4 mounts334 in / 330 out CFM 7 / 5 mounts

With a reference pressure-optimized fan on every mount the The Tower 600 moves more air. The stock fans of the iCUE 5000X RGB SIGNATURE SERIES are named without figures behind them, so its stock columns stay empty. The pressure verdict describes the stock fan set, not the case: stronger or extra intake fans in the free mounts, or slower exhaust fans, turn a negative balance positive.

iCUE 5000X RGB SIGNATURE SERIES — mounts and stock fans

TOPBOTTOMREARFRONT · glass

The Tower 600 — mounts and stock fans

side mountsTOPBOTTOMREARFRONT · glass

Case air heating with the stock fans — computed

0 5 0 100 200 300 400 450 W GPU (open cooler) + 40 W board The Tower 600 K case air above room

Use it

How these numbers are computed

Each stock fan contributes CFMmax · derate · rpm/rpmmax behind its wall's mounting class: filtered mesh front and side mounts as dust filter, bottom as floor + filter, top and rear as open grille, solid and glass fronts as side-slit intake at roughly half of a mesh front. Front, bottom and side blow in; top and rear blow out.

MountingAirflow bladesPressure-optimized
Open grille0.88 (0.80–0.95)0.88 (0.80–0.95)
Dust filter0.70 (0.60–0.80)0.78 (0.70–0.86)
Floor + filter0.64 (0.52–0.74)0.72 (0.62–0.80)
Solid or glass front0.50 (0.40–0.62)0.58 (0.48–0.68)

Worst case sums intake at the low end of each band and exhaust at the high end; positive there means positive regardless of how the estimates fall. Case air: ΔT = 3.1 · W / throughput (m³/h), with an open-cooler GPU putting its full board power into the case air plus board, RAM and drives. Capacity puts a reference pressure-optimized fan on every mount at max rpm — 120 mm 60 CFM, 140 mm 75 CFM — a generic good fan, not a product.

Mount counts, radiator support and clearances are datasheet figures. Nothing here is measured; the same model runs in CaseFlow.